Description

ABE – ECE – CH Approval – Capristo Exhaust System – Gutachten – Abgasanlage

In accordance with Swiss legal requirements, specifically the provisions of the Ordinance on the Technical Requirements for Road Vehicles (OETV; RS 741.41), as well as the specific directives issued by the Swiss Association of Road Traffic Services (ASA), notably ASA Directive 2b, the homologation and commissioning of modified vehicles must comply with the strict standards established by the Federal Roads Office (FEDRO). Compliance with these standards is mandatory to ensure vehicles meet Swiss road traffic regulations.

Important: ABE – ECE – CH Approval – Capristo Exhaust System – Gutachten – Abgasanlage

Pursuant to Article 147 of the OETV, Pfister Autotechnik-Shop reserves the right to withhold the issuance of a Swiss homologation certificate for exhaust systems subject to mandatory inspection if purchased through third-party distributors. This is to ensure full responsibility and product warranty obligations are met.

Information Required for Certificate Issuance:

• Type Approval Number (in accordance with Article 16 of the OETV)
• Vehicle Chassis Number

Technical Specifications and Issuance Conditions:

• Compatibility: Capristo exhaust systems homologated for motor vehicles
• Certificate Validity Conditions:
  • The certificate is valid only with the official stamp and signature of Pfister Autotechnik-Shop
  • No fee if the exhaust system was purchased directly from Pfister Autotechnik-Shop
  • Fee for product purchased from a third-party with valid proof of purchase:
  • Fee for product purchased from a third-party without valid proof of purchase:
• Issued by: Pfister Autotechnik-Shop
• Chassis Number Required: Yes
• Type Approval Required: Yes
• Proof of Purchase Required: Yes

Homologation Procedure in Switzerland : ABE – ECE – CH Approval – Capristo Exhaust System – Gutachten – Abgasanlage

1. Introduction

Modifying an exhaust system in Switzerland requires adherence to strict standards to ensure road safety, environmental compliance, and noise level regulations. This detailed product sheet provides technical specifications, required certifications, and the homologation process, including Swiss-compliant figures for each step.

2. Required Certifications: ABE – ECE – CH Approval – Capristo Exhaust System – Gutachten – Abgasanlage

To homologate an exhaust system, the following certifications are necessary to ensure compliance with Swiss and European standards:

• Teilegutachten:
  • Description: A certificate issued in Germany confirming that the part complies with EU directives.
  • Requirements: The part must comply with European Directive 97/24/EC (modification of exhaust systems). In Switzerland, this certificate must be validated for local specifics.
• DTC Certificate (Dynamic Test Center AG):
  • Institution: Dynamic Test Center AG, accredited by OFROU (Swiss Federal Roads Office).
  • Content: Confirms that the exhaust system meets Swiss standards.
    • Noise Level: Maximum of 80 dB(A) measured at 3/4 of the engine’s maximum speed for light vehicles.
    • Emissions: Pollutant concentrations (CO, HC, NOx) must comply with limits set by the Ordinance on Air Protection (OPair), such as:
      • CO: Maximum 1.0 g/km for gasoline vehicles.
      • NOx: Maximum 0.2 g/km for diesel vehicles.
• FAKT AG Certificate:
  • Institution: FAKT AG, accredited by OFROU.
  • Evaluation:
    • Durability: Resistance test simulating 100,000 km of operation with climatic variations from -20°C to +40°C.
    • Performance: Emissions must not exceed the original values by more than 5%.
• ECE Certificate (Economic Commission for Europe):
  • Description: United Nations certificate for European standards.
  • Compliance: The system must meet European ECE R-59 standards for noise (maximum of 74 dB(A) at 3/4 of the engine’s maximum speed) and emissions.

3. Homologation Process : ABE – ECE – CH Approval – Capristo Exhaust System – Gutachten – Abgasanlage

To homologate a modified exhaust system, follow these steps:

1. Preparation and Installation:
   • Professional Installation: Ensure that the system is installed by an accredited professional to guarantee compliance with technical specifications.
2. Testing and Inspections:
   • Emission Analysis:
     • Test Bench: Conduct tests on a test bench certified according to Swiss standards.
     • Requirements:
       • CO: Maximum 1.0 g/km.
       • HC: Maximum 0.1 g/km for gasoline vehicles.
       • NOx: Maximum 0.2 g/km for diesel vehicles.
   • Acoustic Test:
     • Methodology: Measurements conducted with a microphone placed 0.5 meters from the vehicle under various conditions.
     • Limits: Maximum noise level of 80 dB(A) measured at 3/4 of the engine’s maximum speed for light vehicles.
   • Visual and Mechanical Inspection:
     • Verification: Ensure correct installation, airtight seals, and absence of leaks.
3. Obtaining Certificates:
   • Teilegutachten: Obtain this certificate and validate it for Switzerland.
   • DTC: Submit the system to Dynamic Test Center AG for technical testing.
   • FAKT AG: Complete tests with FAKT AG to obtain the durability and performance certificate.
   • ECE: Ensure that the ECE certificate is valid for European compliance.
4. Submission for Registration:
   • Documents to Submit: Include Teilegutachten, DTC certificates, FAKT AG certificates, ECE, and test reports.
   • Application Form: Complete the homologation application form with technical details and certificates.
5. Final Inspection:
   • Inspection by Cantonal Authority:
     • Criteria: Physical inspection to verify compliance with certificates and local standards.
   • Permit Update:
     • Documentation: Update the vehicle registration to reflect modification details.

4. Technical Standards and Mandatory Tests

To ensure compliance: ABE – ECE – CH Approval – Capristo Exhaust System – Gutachten – Abgasanlage

• Noise Standards (OPB):
  • Limit: Noise level must not exceed 80 dB(A) at 3/4 of the engine’s maximum speed.
  • Procedure: Use calibrated measurement equipment in accordance with Swiss standards.
• Emission Analysis (OPair):
  • Tests: Conducted on a certified test bench with specific limits (e.g., 0.15 g/km HC for gasoline vehicles).
  • Comparison: Results must conform to Euro standards and Swiss directives.
• Durability and Performance Tests:
  • Climatic Testing: Simulate operating conditions with temperature ranges from -20°C to +40°C.
  • Performance Impact: Ensure that fuel consumption and performance do not vary by more than 5% from original specifications.